Huawei UPS2000-G-3 kVA User Manual Download Page 73

Page: 73 / 90

UPS2000-G-3 kVA
User Manual (CTC)

A Alarm Handling

Issue 02 (2019-05-05)

Alarm
ID
(Alarm
ID-Alar
m
Cause)

Alarm
Name

Alarm
Level

Alarm
Clear
Mode

Impact on the System

Repair Proposal

temperature.



Keep the air intake and
exhaust vents of the
UPS unobstructed.



Clean off the foreign
objects around the fan.
If the alarm persists,
contact Huawei
technical support for
repair.

0032-01

Batt.
OVP

Critical

Automatic
clear

An alarm is generated, and
the battery lifespan is
affected.

Possible causes:



The configured number
of batteries is less than
the actual number.



The actual number of
batteries does not meet
specifications.



The charger is
abnormal.

Measures:



Check that the
configured number of
batteries matches the
actual number.



Check that the actual
number of batteries
meets requirements.



Disconnected the
external battery charger,
check whether the alarm
is cleared. If not,
contact Huawei
technical support for
repair.

0034-01

Remaini
ng cap.
warning

Minor

Automatic
clear

If no action is taken,
continued discharge will
result in system shutdown
due to EOD.

Possible cause:



The battery discharge
lasts too long.



The mains input is
abnormal.



The number of batteries
or battery capacity is
incorrectly set.

Summary of Contents for UPS2000-G-3 kVA



























































































Search results

Summary of Contents for UPS2000-G-3 kVA

Reviews:

Related manuals for UPS2000-G-3 kVA

Brands by name

Popular brands

Huawei UPS2000-G-3 kVA, User Manual

Search results

Summary of Contents for UPS2000-G-3 kVA

Reviews:

Related manuals for UPS2000-G-3 kVA

Brands by name

Popular brands