Huawei UPS2000-G-3 kVA User Manual Download Page 60

Page: 60 / 90

UPS2000-G-3 kVA
User Manual (CTC)

7 UPS Maintenance

Issue 02 (2019-05-05)

Check Item

Expected Result

Troubleshooting

Maintenance
Interval

displayed in active
alarm or historical
alarms.

Cleanliness

Wipe the UPS
surface using a
white paper and the
paper does not turn
black.

Clean the dust,
especially in the
front panel.

Quarterly

Parameter

Check the output
voltage level and
frequency, the
number of batteries
and the actual
battery capacity.

Reset the
parameters.

Quarterly

Power cables and
terminals (between
the UPS and the
power distribution
cabinet)

The insulation layers
of cables are intact
and terminals are
free from noticeable
sparks.



Replace the
cables.



Secure the output
terminals.

Quarterly

EPO (if configured)

Check the reliability
of the EPO cable
connection.

Secure the terminals. Yearly

Summary of Contents for UPS2000-G-3 kVA



























































































Search results

Summary of Contents for UPS2000-G-3 kVA

Reviews:

Brands by name

Popular brands

Huawei UPS2000-G-3 kVA, User Manual

Search results

Summary of Contents for UPS2000-G-3 kVA

Reviews:

Brands by name

Popular brands