background image

UPS2000-G-3 kVA 
User Manual (CTC) 

A Alarm Handling 

 

Issue 02 (2019-05-05) 

Copyright © Huawei Technologies Co., Ltd. 

71 

 

Alarm 
ID 
(Alarm 
ID-Alar

Cause) 

Alarm 
Name 

Alarm 
Level 

Alarm 
Clear 
Mode 

Impact on the System 

Repair Proposal 

technical support for repair. 

0042-09 

Internal 
fault 

Critical 

Automatic 
clear 

The inverter shuts down. 

Possible cause: Self-load 
cable connections are 
incorrect. 

Measure: Reconnect 
cables. 

0042-10 

Internal 
fault 

Critical 

Automatic 
clear 

If the inverter has not started, 
the UPS has no output, and 
inverter startup is not 
allowed. 

If the inverter has started, 
inverter operation is not 
affected, but transfer to 
bypass mode is not allowed. 

Possible cause: The bypass 
input cable connections do 
not match the output 
system. 

Measure: Ensure that the 
bypass input cable 
connections match the 
output system. 

0042-11 

Internal 
fault 

Critical 

Power-off 
clear 

After the parallel system is 
powered on, an incorrect 
bypass phase sequence is 
detected on a UPS. The 
parallel system has not 
output. 

The parallel system works in 
inverter mode. The newly 
added UPS has no output 
because bypass cables are 
incorrectly connected. 

The parallel system works in 
bypass mode. The parallel 
system has no output because 
bypass cables for the newly 
added UPS are incorrectly 
connected. 

Possible cause: The bypass 
phase sequences in the 
parallel system do not 
match. 

Measure: Check bypass 
input phase sequences in 
the parallel system. 

0042-12 

Internal 
fault 

Critical 

Manual 
clear/Power
-off clear 

The UPS startup is not 
allowed. 

Possible cause: The 
three-phase power cable 
lengths vary greatly. 

Measure: Ensure that the 
lengths of three-phase 
power cables vary within a 
difference of 5%. 

0042-13 

Internal 
fault 

Critical 

Manual 
clear/Power
-off clear 

The UPS startup is not 
allowed. 

Possible cause: The 
inverter is faulty. 

Measure: Contact Huawei 
technical support for repair. 

Summary of Contents for UPS2000-G-3 kVA



























































































Reviews: