manualshive.com logo in svg

Huawei UPS2000-G-3 kVA, User Manual

Share
Download
Huawei UPS2000-G-3 kVA User Manual Download Page 69

UPS2000-G-3 kVA 
User Manual (CTC) 

A Alarm Handling 

 

Issue 02 (2019-05-05) 

Copyright © Huawei Technologies Co., Ltd. 

63 

 

Alarm 
ID 
(Alarm 
ID-Alar
m 
Cause) 

Alarm 
Name 

Alarm 
Level 

Alarm 
Clear 
Mode 

Impact on the System 

Repair Proposal 

bypass input frequency 
exceeds the configured 
range. If yes, change the 
range or wait until the 
bypass input recovers. 

0011-01 

BPS 
phase 
reverse 

Minor 

Automatic 
clear 

 

If the inverter has not 
started, the system has no 
output, and inverter 
startup is prohibited. 

 

If the inverter has started, 
the inverter still works 
properly, but the system 
cannot transfer to bypass 
mode. 

Possible cause: The bypass 
input three-phase sequence 
is incorrect. 

Measure: Check that 
bypass input power cables 
are correctly connected. 

0012-01 

BPS 
neutral 
loss 

Minor 

Automatic 
clear 

If the inverter has not started, 
the system has no output, and 
inverter startup is prohibited. 

If the inverter has started, the 
inverter still works properly, 
but the system cannot 
transfer to bypass mode. 

Possible cause: The bypass 
input neutral wire is not 
connected. 

Measures: Check that 
bypass input power cables 
are correctly connected. 

0014-01 

Start 
timeout 

Critical 

Manual 
clear/Power
-off clear 

The UPS cannot start. 

Possible causes: 

 

The bypass load 
exceeds the rated 
inverter load. 

 

An internal fault occurs 
in the UPS. 

Measures: 

 

Reduce the output load, 
manually clear the 
alarm, and restart the 
UPS. 

 

Contact Huawei 
technical support for 
repair. 

0020-01 

Batt. 
reverse 

Critical 

Automatic 
clear 

The power supply from the 
UPS and system is not 
affected. 

Possible cause: Batteries 
are reversely connected. 

Measure: Check the battery 
installation, and reinstall 
the batteries. 

0022-01 

No 

Minor 

Automatic 

The power supply from the 
UPS and system is not 

Possible causes: 

Summary of Contents for UPS2000-G-3 kVA



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands