Huawei SUN2000-28KTL Quick Installation Manual Download Page 23

Page: 23 / 27

SUN2000 (8KTL-28KTL)
Quick Installation Guide

Issue 04 (2013-12-12)

Huawei Proprietary and Confidential

You are recommended to use 24 AWG outdoor shielded network cables with the internal
resistance less than or equal to 1.5 ohms/10 m and external diameter of 4.5 mm to 7.5 mm as
RS485 communications cables.

Step 2

Insert the shielded network cable into the sealing nut, seals, screw nut, and housing.

Step 3

Connect the stripped network cable to corresponding pins on the plug, as shown in

Figure

1-30

Figure 1-30

Connecting a communications cable (1)

Figure 1-30

shows the side without a clip.

Table 1-2

lists the cable colors and functions.

Table 1-2

Cable colors and functions

No.

Color

Function

White and orange

RS485A, RS485 differential

Orange

RS485B, RS485 differential signal
-

White and green

PGND

Blue

RS485A, RS485 differential

White and blue

RS485B, RS485 differential signal
-

Green

PGND

White and brown

PGND

Brown

PGND

Summary of Contents for SUN2000-28KTL




























Search results

Summary of Contents for SUN2000-28KTL

Reviews:

Related manuals for SUN2000-28KTL

Brands by name

Popular brands

Huawei SUN2000-28KTL, Quick Installation Manual

Search results

Summary of Contents for SUN2000-28KTL

Reviews:

Related manuals for SUN2000-28KTL

Brands by name

Popular brands