Huawei SUN2000-28KTL Quick Installation Manual Download Page 15 | Manualshive

Page: 15 / 27

background image

SUN2000 (8KTL-28KTL)
Quick Installation Guide

Issue 04 (2013-12-12)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

13

Figure 1-14

Mounting the SUN2000 on the rear panel (rear view)

5.

Tighten the two hexagon screws at the bottom the SUN2000 (tightening torque of 5
N.m), and then install an anti-theft lock, as shown in

Figure 1-15

.

You can secure the SUN2000 to the rear panel and protect it from stealing by installing
an anti-theft lock, but this action is optional.

Figure 1-15

Tightening hexagon screws

----End

«
...
13
14
15
16
17
...
»

Summary of Contents for SUN2000-28KTL




























Reviews:

No comments

Related manuals for SUN2000-28KTL

VIP-5000 Series

Brand: Daktronics Pages: 6

Brand: Daikin Pages: 255

Brand: Harmonic Pages: 27

Brand: Samson Pages: 58

Brand: Z3 Technology Pages: 86

HOME NERATOR SYSTEM 18000 WATT

Brand: GE Pages: 84

Brand: ICP DAS USA Pages: 3

Brand: Zlpower Pages: 24

Slimline Plus 1250

Brand: Wagan Pages: 32

Brand: HEIDENHAIN Pages: 44

Brand: LogicLadder Pages: 55

Adaptatone 5530M-485 Series

Brand: Edwards Signaling Pages: 13

DEMO CIRCUIT 1672A

Brand: Linear Technology Pages: 13

Video Sweep Generator MVG 10

Brand: Kathrein Pages: 28

Brand: Miteq Pages: 55

Brand: Fronius Pages: 92

Brand: IMO Pages: 16

Brand: Peak Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands