Huawei SUN2000-28KTL Quick Installation Manual Download Page 21 | Manualshive

Page: 21 / 27

background image

SUN2000 (8KTL-28KTL)
Quick Installation Guide

Issue 04 (2013-12-12)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

19

7. Connecting DC Input Power Cables

Step 1

Remove cable glands from the positive and negative connectors.

Step 2

Remove the insulation layer with an appropriate length from the positive and negative power
cables by using a wire stripper as show in

Figure 1-27

.

PV power cables with a cross-sectional area of 4 mm

2

are recommended.

Figure 1-27

Connecting DC input power cables (1)

1. Positive power cable

2. Negative power cable

Note: L2 is 2 to 3 mm longer than L1.

PV power cables with a cross-sectional area of 4 mm

2

are recommended.

Step 3

Insert the positive and negative power cables into corresponding cable glands.

Step 4

Insert the stripped positive and negative power cables into the positive and negative metal
terminals respectively and crimp them using a clamping tool. Ensure that the cables are
crimped until they cannot be pulled out by force less than 400 N, as shown in

Figure 1-28

.

«
...
19
20
21
22
23
...
»

Summary of Contents for SUN2000-28KTL




























Reviews:

No comments

Related manuals for SUN2000-28KTL

Brand: NAIM Pages: 36

Brand: NAIM Pages: 17

Brand: PowerConnections Pages: 10

Vertex VCE6-HFC-4C

Brand: Spirent Pages: 8

Brand: Karma Pages: 2

Brand: NewTek Pages: 14

Brand: Platinum Pages: 82

Brand: NSM Pages: 24

Brand: Delta Pages: 1

Brand: KDS Pages: 4

BLANKOM SDE-1265

Brand: Irenis Pages: 22

Brand: Systech Corporation Pages: 6

YUAN SC710N4 HDMI2.0

Brand: JMC Pages: 8

Brand: Kramer Pages: 16

Brand: Monoprice Pages: 4

Brand: MRC Pages: 6

HOME NERATOR SYSTEM 12000 WATT

Brand: GE Pages: 80

Demultiplexer 30/60 Box

Brand: MA lighting Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands