Huawei Quidway S1700-24-AC Manual Download

Page: 163 / 266

Attribute

Description

Maximum

transmission

distance

100 m

1000BASE-X port

When a 1000BASE-X port uses a GE optical module, it can only transmit and

receive data at 1000 Mbit/s and does not support the 100 Mbit/s transmission

speed. When a 1000BASE-X port uses a GE copper module, it can transmit and

receive data at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s.

Table 5-40

describes the

attributes of a 1000BASE-X port.

Table 5-40

Attributes of a 1000BASE-X port

Attribute

Description

Connector type

LC/PC

Optical port

attributes

Depend on the module used

Standards

compliance

IEEE802.3z

Console port

The console port is connected to a console for on-site configuration.

Table 5-41

describes the attributes of the console port.

Table 5-41

Attributes of the console port

Attribute

Description

Connector type

RJ45

Standards

compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200

bit/s
Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management

workstation through the ETH management port to configure the switch locally or

S1700 Managed Series Ethernet Switches

Product Description

5 Hardware Structure

Issue 18 (2020-10-23)

129

Summary of Contents for Quidway S1700-24-AC











































































































































































































































































Search results

Summary of Contents for Quidway S1700-24-AC

Reviews:

Related manuals for Quidway S1700-24-AC

Brands by name

Popular brands

Huawei Quidway S1700-24-AC, Manual

Search results

Summary of Contents for Quidway S1700-24-AC

Reviews:

Related manuals for Quidway S1700-24-AC

Brands by name

Popular brands