Huawei Quidway S1700-24-AC Manual Download

Page: 155 / 266

Display

Mode

Color

Status

Description

Green

Steady on A link has been established on the port.

Yellow

Blinking

The port is sending or receiving data.

Speed

Off

The port is not connected or has been

shut down.

Green

and

yellow

Steady on 1000M/10GE port: The port is operating

at 1000 Mbit/s.

Green

and

yellow

Blinking

1000M/10GE port: The port is operating

at 10 Gbit/s.

Power Supply Configuration

The S1720X-16XWR has a built-in power module and does not support pluggable

power modules.

Heat Dissipation

The S1720X-16XWR has three built-in fans for forced air cooling. Air flows in from

the left side and front panel, and exhausts from the right side.

Technical Specifications

Table 5-37

lists technical specifications of the S1720X-16XWR.

Table 5-37

Technical specifications

Item

Description

Memory (RAM)

1 GB

Flash

512 MB in total, 240 MB available for customers

Mean time

between failures

(MTBF)

37.9 years

Mean time to

repair (MTTR)

2 hours

Availability

> 0.99999

Service port

surge protection

N/A

Power supply

surge protection

±6 kV in differential mode, ±6 kV in common mode

S1700 Managed Series Ethernet Switches

Product Description

5 Hardware Structure

Issue 18 (2020-10-23)

121

Summary of Contents for Quidway S1700-24-AC











































































































































































































































































Search results

Summary of Contents for Quidway S1700-24-AC

Reviews:

Related manuals for Quidway S1700-24-AC

Brands by name

Popular brands

Huawei Quidway S1700-24-AC, Manual

Search results

Summary of Contents for Quidway S1700-24-AC

Reviews:

Related manuals for Quidway S1700-24-AC

Brands by name

Popular brands