Huawei FusionModule2000 V500R003C10 Product Description Download Page 56 | Manualshive

Page: 56 / 217

background image

FusionModule2000 Smart Modular Data Center
Product Description

5 Power Supply and Distribution System

Issue 06 (2020-05-21)

Copyright © Huawei Technologies Co., Ltd.

48

Indicator

Color

Status

Description

0.125s).

Off

The bypass software is being
upgraded.

Alarm indicator

Yellow

Steady on

A minor alarm is generated
for the bypass.

Off

There is no minor alarm for
the bypass, or the software is
being upgraded.

Fault indicator

Red

Steady on

A critical alarm is generated
for the bypass.

Off

There is no critical alarm for
the bypass, or the software is
being upgraded.

Functions

The bypass module supplies power in the following cases:

If the UPS is set to ECO mode and the bypass voltage is within the specified range, the UPS
works in bypass mode.

If the power module overload times out, the UPS transfers to bypass mode.

Both the active and standby ECMs are abnormal.

The system fails to run properly and transfers to bypass mode.

A manual operation is performed to transfer to bypass mode.

Specifications



Dimensions (H x W x D): 130 mm x 420 mm x 500 mm



Weight: 19 kg



Rated output capacity: 200 kVA

5.2.2.4 Control Module

5.2.2.4.1 Overview

In a standard configuration, the control module consists of two ECMs, one dry contact card,
and one monitoring interface card (from left to right). The four cards are hot swappable. One
subrack is reserved above the dry contact card. A backfeed protection card or dry contact
extended card can be inserted into this subrack.

«
...
54
55
56
57
58
...
»

Summary of Contents for FusionModule2000 V500R003C10


























































































































































































































Reviews:

No comments

Related manuals for FusionModule2000 V500R003C10

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

Brand: IBM Pages: 4

WS-650 lite Series

Brand: Laurell Pages: 84

Brand: YASKAWA Pages: 68

Brand: 3Com Pages: 16

Brand: Planet Pages: 20

Brand: STONEFLY Pages: 48

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

Brand: Amplifier Tech Pages: 36

Brand: H3C Pages: 26

Brand: Grizzly Pages: 9

Brand: VCS Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands