Huawei FusionModule2000 V500R003C10 Product Description Download Page 162

Page: 162 / 217

FusionModule2000 Smart Modular Data Center
Product Description

8 Intelligent Module Management System

Issue 06 (2020-05-21)

154

8.3.1.3 Power Module

Indicator

Table 8-16

PSU indicator description

Indicator

Color

Name

Status

Description

Green

Power
indicator

Steady on

The converter has a power
input.

Off

The converter has no
power input or is faulty.

Blinking at
long
intervals

The converter is being
queried (the indicator
blinks at 0.5 Hz, on for 1s
and then off for 1s).

Blinking at
short
intervals

The converter application
program is being loaded
(the indicator blinks at 4
Hz, on for 0.125s and then
off for 0.125s).

Yellow

Alarm
indicator

Steady on

The converter generates a
forewarning indicating that
power will be limited due
to ambient
overtemperature, or
generates a protection
shutdown alarm due to
ambient overtemperature
or undertemperature.

Power input overvoltage
or undervoltage protection

Reverse DC input
connection

Slight current imbalance

Output overvoltage

Hibernation

Off

The converter generates no
protection alarms.

Blinking at
long
intervals

The communication
between the converter and
the outside is interrupted
(the indicator blinks at 0.5
Hz, on for 1s and then off
for 1s).

Red

Fault

Steady on

The converter locks out

Summary of Contents for FusionModule2000 V500R003C10


























































































































































































































Search results

Summary of Contents for FusionModule2000 V500R003C10

Reviews:

Related manuals for FusionModule2000 V500R003C10

Brands by name

Popular brands

Huawei FusionModule2000 V500R003C10, Product Description

Search results

Summary of Contents for FusionModule2000 V500R003C10

Reviews:

Related manuals for FusionModule2000 V500R003C10

Brands by name

Popular brands