Huawei FusionModule2000 V500R003C10 Product Description Download Page 160

Page: 160 / 217

FusionModule2000 Smart Modular Data Center
Product Description

8 Intelligent Module Management System

Issue 06 (2020-05-21)

152

Item

Description

Pin 3

12 V DC_OUT

Pin 4

N/A

Pin 5

N/A

Pin 6

Pin 7

DO_OUT-

Pin 8

GND

Indicator

Green
indicator

Power output indicator



Steady on: The 12 V DC output is normal.



Off: No 12 V DC output is provided.

Table 8-13

USB port pin definitions

Item

Description

Pin sequence

Pin 1

5 V

Pin 2

Pin 3

Pin 4

GND

Indicators

Table 8-14

Indicators on the ECC800-Pro main control module

Indicator

Color

Name

Status

Description

RUN

Green

Running
status
indicator

Steady on

The power supply is normal, the
program is being loaded.

Off

The power supply is abnormal.

Blinking at
long
intervals

The software runs properly (the
indicator blinks at 0.5 Hz, on for
1s and then off for 1s) or the
ECC800-Pro registers with the
NetEco successfully.

Blinking at
short
intervals

The ECC800-Pro does not
register with the NetEco (the
indicator blinks at 5 Hz, on for
0.125s and then off for 0.125s).

ALM

Red

Alarm

Steady on

A system failure alarm is

Summary of Contents for FusionModule2000 V500R003C10


























































































































































































































Search results

Summary of Contents for FusionModule2000 V500R003C10

Reviews:

Related manuals for FusionModule2000 V500R003C10

Brands by name

Popular brands

Huawei FusionModule2000 V500R003C10, Product Description

Search results

Summary of Contents for FusionModule2000 V500R003C10

Reviews:

Related manuals for FusionModule2000 V500R003C10

Brands by name

Popular brands