HP t505 Troubleshooting Manual Download

Page: 10 / 71

Rear Panel Components

For more information, go to

http://www.hp.com

and search for your specific thin client model to find

the model-specific QuickSpecs.

Figure 1-3

Rear panel components

(1)

Ethernet RJ-45 connector

(5)

Cable lock slot

(2)

Serial connectors (4)

(6)

Power connector

(3)

Parallel connector

(7)

VGA connector

(4)

PS/2 connectors (2)

(8)

Universal serial bus (USB) connectors (2)

Installing the Rubber Feet

You may want to use your thin client in a horizontal orientation. You can install rubber feet on the left
side of the unit to help keep the unit safely in place.

To install the rubber feet:

Locate the VESA (Video Electronics Standards Association) holes in the left side of the thin
client.

CAUTION:

If you use the thin client in a horizontal orientation without the rubber feet, it may

slide and result in equipment damage.

Remove the feet from their backing.

Chapter 1 Product Description

Summary of Contents for t505








































































Search results

Summary of Contents for t505

Reviews:

Related manuals for t505

Brands by name

Popular brands

HP t505, Troubleshooting Manual

Search results

Summary of Contents for t505

Reviews:

Related manuals for t505

Brands by name

Popular brands