manualshive.com logo in svg

HP StoreOnce 4900 Backup, Installation And Configuration Manual

Share
Download
HP StoreOnce 4900 Backup Installation And Configuration Manual Download Page 58

ipaddr 10.2.1.55 gateway 10.2.1.1 netmask 255.255.0.0 domain sales.mycompany.net 

 nl   

default no vlantag 23

Command Successful

4.

Check the configuration again.

# net show config ACMECorpNetwork1

----------------------
Network Name: ACMECorpNetwork1
Network Description: Created by wizard on: Wed Apr 30 15:26:40 2014
Write Protected: no
DNS Servers: 172.1.1.100 172.1.2.100
Port Sets: portset_1 portset_2 portset_3
----------------------
Number of Networks: 4
Number of VLANs configured: 2 out of possible 128
----------------------
Network: subnet_1
----------------------
IP Addresses: dhcp
Net Mask: dhcp
Domain Name: dhcp
Gateway: dhcp
Default Network:
VLAN tag:
Port Set: portset_1 with these interfaces: eth0
Encryption Links:
Bonding Mode: Not applicable----------------------
Network: subnet_2
----------------------
IP Addresses: 10.1.1.21
Net Mask: 255.255.0.0
Domain Name: rnd.mycompany.net
Gateway: 10.1.1.1
Default Network:
VLAN tag: 22
Port Set: portset_2 with these interfaces: eth5 eth7
Encryption Links:
Bonding Mode: 4 (Link Aggregate Control Protocol (LACP) Bonding)
----------------------
Network: subnet_3
----------------------
IP Addresses: 172.1.1.66
Net Mask: 255.255.0.0
Domain Name: uk.mycompany.net
Gateway: 172.1.1.1
Default Network: yes
VLAN tag:
Port Set: portset_3 with these interfaces: eth2 eth3
Encryption Links:
Bonding Mode: 6 (Active Load Balance Bonding)
----------------------
Network: SalesSubnet
----------------------
IP Addresses: 10.2.1.55
Net Mask: 255.255.0.0
Domain Name: sales.mycompany.net
Gateway: 10.2.1.1
Default Network: no
VLAN tag: 24
Port Set: portset_2 with these interfaces: eth5 eth7
Encryption Links:
Bonding Mode: 4 (Link Aggregate Control Protocol (LACP) Bonding)

Command Successful

58

Network configuration, how to use StoreOnce CLI commands

Summary of Contents for StoreOnce 4900 Backup





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands