HP J2600A Installation Manual Download Page 81

Page: 81 / 104

HP Cables

The following table lists HP cables for the WAN port. For information
about cables that can be used to connect a console to the hub’s RS-232
Distributed Management port, refer to the hub’s installation guide.

Cable

Connector on Attached Device

HP Product or Part Number

V.35 cable (balanced X.27)

For 34-pin female port

28606-63008 (5 meters)

RS-232/V.24/V.28 cable

For 25-pin female port

28606-63006 (5 meters) *

X.21 cable

For 15-pin female port

28606-63001 (5 meters)

RS-422/RS-449/V.36 cable

For 37-pin female port

28606-63005 (5 meters)

Back-to-Back test cable for WAN port
connecting to HP routers having a 62-
pin synchronous WAN port or to the
HP Remote Bridge RB

For 62-pin female WAN port(s)
included on most HP routers
and the HP Remote Bridge RB

5061-2556 (5 meters)

* For this cable, the maximum speed supported on the WAN is 64 Kbit/s.

Cables and Connectors

HP Cables

A-3

Summary of Contents for J2600A








































































































Search results

Summary of Contents for J2600A

Reviews:

Related manuals for J2600A

Brands by name

Popular brands

HP J2600A, Installation Manual

Search results

Summary of Contents for J2600A

Reviews:

Related manuals for J2600A

Brands by name

Popular brands