HP HP-UX 11i v3 Administrator'S Manual Download Page 85

Page: 85 / 125

7 Support and other resources

Contacting HP

Documentation feedback

HP welcomes your feedback. To make comments and suggestions about product documentation,
send a message to:

http://www.hp.com/bizsupport/feedback/ww/webfeedback.html

Include the document title and manufacturing part number. All submissions become the property
of HP.

New and changed information in this edition

The January 2008 release of HP APA for HP-UX 11i v3 provides IPoIB support and support for
fixed MAC address assignment.

Revision history

Publication Date

Edition Number

Supported Versions

Supported Operating
Systems

Manufacturing Part
Number

January 2010

E1001

B.11.31.0909

11i v3

J4240–90049

September 2008

E1207

B.11.00.xx
B.11.11.30
B.11.23.40
B.11.31.10

11.0
11i v1
11i v2

J4240–90046

September 2008

E0908

B.11.31.20

11i v3

J4240–90045

December 2007

E1207

B.11.00.xx
B.11.11.30
B.11.23.40
B.11.31.10

11.0
11i v1
11i v2
11i v3

J4240–90041

September 2007

E0907

B.11.00.xx
B.11.11.30
B.11.23.30

11.0
11i v1
11i v2

J4240–90039

February 2007

E0207

B.11.31.02

11i v3

J4240–90037

Related information

Documents

•

HP Auto Port Aggregation (APA) Release Notes

•

Performance and Scalability White Paper

•
•

Using APA to Build a Screaming Fast Network Server Connection

Typographic conventions

This document uses the following typographical conventions:

Contacting HP

Summary of Contents for HP-UX 11i v3






























































































































Search results

Summary of Contents for HP-UX 11i v3

Reviews:

Related manuals for HP-UX 11i v3

Brands by name

Popular brands

HP HP-UX 11i v3, Administrator'S Manual

Search results

Summary of Contents for HP-UX 11i v3

Reviews:

Related manuals for HP-UX 11i v3

Brands by name

Popular brands