HP HP-UX 11i v3 Administrator'S Manual Download Page 26

Page: 26 / 125

Figure 3-5 Sample Hot Standby Configuration for High Availability

HP APA 2-Port Hot

Standby Link Aggregation

Switch

or Hub

Switch

or Hub

Power

Run Attn.

Fault

Remote

Primary

Standby

Server-to-Server with switch (not recommended)

Figure 3-6 (page 27)

shows a sample server–to–server HP APA link aggregation configuration

with a switch between the servers. This configuration will not work as intended for the following
reasons:
•

The switch nullifies any load balancing of network traffic provided by HP APA.

•

The switch uses a MAC address load-balancing algorithm. Because the servers' link
aggregations have fixed MAC addresses, the switch will not load balance; it will only transmit
data on one physical link.

Configuring APA

Summary of Contents for HP-UX 11i v3






























































































































Search results

Summary of Contents for HP-UX 11i v3

Reviews:

Related manuals for HP-UX 11i v3

Brands by name

Popular brands

HP HP-UX 11i v3, Administrator'S Manual

Search results

Summary of Contents for HP-UX 11i v3

Reviews:

Related manuals for HP-UX 11i v3

Brands by name

Popular brands