HP A7L26UT#ABA Maintenance And Service Manual Download Page 27

Page: 27 / 200

Recovering the Configuration Settings

This method of recovery requires that you first perform the

Save to Removable Media

command

with the Computer Setup (F10) Utility before

Restore

is needed.

NOTE:

It is recommended that you save any modified computer configuration settings to a USB

flash media device and save the device for possible future use.

To restore the configuration, insert the USB flash media device with the saved configuration and
perform the

Restore from Removable Media

command with the Computer Setup (F10) Utility.

Recovering the Configuration Settings

Summary of Contents for A7L26UT#ABA









































































































































































































Search results

Summary of Contents for A7L26UT#ABA

Reviews:

Related manuals for A7L26UT#ABA

Brands by name

Popular brands

HP A7L26UT#ABA, Maintenance And Service Manual

Search results

Summary of Contents for A7L26UT#ABA

Reviews:

Related manuals for A7L26UT#ABA

Brands by name

Popular brands