manualshive.com logo in svg

HP A7L26UT#ABA, Maintenance And Service Manual

The HP A7L26UT#ABA user manual is a useful brochure that provides detailed instructions on operating and troubleshooting your device. Easily download it for free from manualshive.com, enabling you to maximize the performance of your HP A7L26UT#ABA without any hassle.

Share
Download
background image

Solving Diskette Problems

Common causes and solutions for diskette problems are listed in the following table.

NOTE:

The computer does not support internal diskette drives. Only USB diskette drives are

supported.

NOTE:

You may need to reconfigure the computer when you add or remove hardware, such as an

additional diskette drive. See 

Solving Hardware Installation Problems on page 163

 for instructions.

Table D-3

  Solving Diskette Problems

Diskette drive light stays on.

Cause

Solution

Diskette is damaged.

Right-click 

Start

, click 

Explore

, and right-click on a drive.

Select 

Properties

 then select the 

Tools

 tab. Under 

Error-

checking

 click 

Check Now

.

Diskette is incorrectly inserted.

Remove diskette and reinsert.

Drive cable is not properly connected.

Reconnect drive cable. Ensure that all four pins on the
diskette power cable are connected to the drive.

Drive not found.

Cause

Solution

Cable is loose.

Reseat diskette drive data and power cable.

Removable drive is not seated properly.

Reseat the drive.

The device has been hidden in Computer Setup.

Run the Computer Setup utility and ensure 

Device Available

is selected for the Legacy Diskette in 

Security

 > 

Device

Security

.

Diskette drive cannot write to a diskette.

Cause

Solution

Diskette is not formatted.

Format the diskette.

1.

From Windows Explorer select the disk 

(A)

 drive.

2.

Right-click the drive letter and select 

Format

.

3.

Select the desired options, and click 

Start

 to begin

formatting the diskette.

Diskette is write-protected.

Use another diskette or remove the write protection.

Writing to the wrong drive.

Check the drive letter in the path statement.

Not enough space is left on the diskette.

1.

Use another diskette.

2.

Delete unneeded files from diskette.

Diskette is damaged.

Replace the damaged disk.

Solving Diskette Problems 147

Summary of Contents for A7L26UT#ABA









































































































































































































Reviews:

No comments

Related manuals for A7L26UT#ABA

Harbor Freight Tools 03648 Assembly Instructions preview
03648
Brand: Harbor Freight Tools Pages: 4
NEC SP B-Series Service And Reference Manual preview
SP B-Series
Brand: NEC Pages: 146
EUROCOM LP295UB User Manual preview
LP295UB
Brand: EUROCOM Pages: 176
XPLORE TECHNOLOGIES iX104C6 Quick Start Manual preview
iX104C6
Brand: XPLORE TECHNOLOGIES Pages: 2
AXIOMTEK GOT-5100TL User Manual preview
GOT-5100TL
Brand: AXIOMTEK Pages: 65
Quanmax QutePC-2000 User Manual preview
QutePC-2000
Brand: Quanmax Pages: 34
Seville Classics OFF65864 AIRLIFT 25 Quick Start Manual preview
OFF65864 AIRLIFT 25
Brand: Seville Classics Pages: 4
Packard Bell oneTwo M3350 Service Manual preview
oneTwo M3350
Brand: Packard Bell Pages: 122
XtendLan TC-965 User Manual preview
TC-965
Brand: XtendLan Pages: 65
Sony VAIO PCG-V505DC2 Series Specifications preview
VAIO PCG-V505DC2 Series
Brand: Sony Pages: 2
Sony VAIO MX PCV-MXS10 Specifications preview
VAIO MX PCV-MXS10
Brand: Sony Pages: 1
Sony VAIO Fit 14 Quick Start Manual preview
VAIO Fit 14
Brand: Sony Pages: 2
Sony VAIO E Series SVE111 Quick Start Manual preview
VAIO E Series SVE111
Brand: Sony Pages: 2
Sony VAIO PCG-C1MW Service Manual preview
VAIO PCG-C1MW
Brand: Sony Pages: 11
Sony VAIO PCG-TR3 Series Service Manual preview
VAIO PCG-TR3 Series
Brand: Sony Pages: 17
Sony VAIO PCG6C1L Quick Start Manual preview
VAIO PCG6C1L
Brand: Sony Pages: 44
Sony VAIO MX PCV-MXS10 Service Manual preview
VAIO MX PCV-MXS10
Brand: Sony Pages: 32
Sony VAIO PCG-TR3 Series Quick Start Manual preview
VAIO PCG-TR3 Series
Brand: Sony Pages: 40

Brands by name

Popular brands

Load more brands