manualshive.com logo in svg

HP A7L26UT#ABA, Maintenance And Service Manual

The HP A7L26UT#ABA user manual is a useful brochure that provides detailed instructions on operating and troubleshooting your device. Easily download it for free from manualshive.com, enabling you to maximize the performance of your HP A7L26UT#ABA without any hassle.

Share
Download
background image

Table D-12

  Solving Network Problems (continued)

Network status link light never flashes.

NOTE:

The network status light is supposed to flash when there is network activity.

Cause

Solution

Network controller is disabled.

1.

Run Computer Setup and enable network controller.

2.

Enable the network controller in the operating system
via Device Manager.

Network driver is not properly loaded.

Reinstall network drivers.

System cannot autosense the network.

Disable auto-sensing capabilities and force the system into
the correct operating mode.

Diagnostics reports a failure.

Cause

Solution

The cable is not securely connected.

Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely
attached to the correct device.

The cable is attached to the incorrect connector.

Ensure that the cable is attached to the correct connector.

There is a problem with the cable or a device at the other
end of the cable.

Ensure that the cable and device at the other end are
operating correctly.

Network controller interrupt is shared with an expansion
board.

Under the Computer Setup 

Advanced

 menu, change the

resource settings for the board.

The network controller is defective.

Contact an authorized service provider.

Diagnostics passes, but the computer does not communicate with the network.

Cause

Solution

Network drivers are not loaded, or driver parameters do not
match current configuration.

Make sure the network drivers are loaded and that the driver
parameters match the configuration of the network controller.

Make sure the correct network client and protocol is installed.

The network controller is not configured for this computer.

Select the 

Network

 icon in the 

Control Panel

 and configure

the network controller.

Network controller stopped working when an expansion board was added to the computer.

Cause

Solution

Network controller interrupt is shared with an expansion
board.

Under the Computer Setup 

Advanced

 menu, change the

resource settings for the board.

The network controller requires drivers.

Verify that the drivers were not accidentally deleted when the
drivers for a new expansion board were installed.

The expansion board installed is a network card (NIC) and
conflicts with the embedded NIC.

Under the Computer Setup 

Advanced

 menu, change the

resource settings for the board.

166 Appendix D   Troubleshooting Without Diagnostics

Summary of Contents for A7L26UT#ABA









































































































































































































Reviews:

No comments

Related manuals for A7L26UT#ABA

Cobalt Digital Inc HPF-9000 Product Manual preview
HPF-9000
Brand: Cobalt Digital Inc Pages: 54
INTERACT AS-1004 Owner'S Manual preview
AS-1004
Brand: INTERACT Pages: 15
Elo TouchSystems B-series Quick Installation Manual preview
B-series
Brand: Elo TouchSystems Pages: 3
Foxconn R10-S3 Manual preview
R10-S3
Brand: Foxconn Pages: 2
Vivo DESK-V000A Instruction Manual preview
DESK-V000A
Brand: Vivo Pages: 3
GE 235 System Manual preview
235
Brand: GE Pages: 112
GE Centricity RA600 Service Manual preview
Centricity RA600
Brand: GE Pages: 278
Black & Decker FSWM1000 Instruction Manual preview
FSWM1000
Brand: Black & Decker Pages: 20
Wincor Nixdorf P4-EPC/B-E1 Operating Manual preview
P4-EPC/B-E1
Brand: Wincor Nixdorf Pages: 32
Rockwell Allen-Bradley VersaView 6300B Installation Instructions Manual preview
Allen-Bradley VersaView 6300B
Brand: Rockwell Pages: 8
Diamond Systems GPIO-MM Manual preview
GPIO-MM
Brand: Diamond Systems Pages: 9
Uninet 2000 NION-MXL Instruction Manual preview
2000 NION-MXL
Brand: Uninet Pages: 20
Rikomagic MK802 II Manual preview
MK802 II
Brand: Rikomagic Pages: 19
Elster Instromet enCore FC1 Operating Instructions Manual preview
enCore FC1
Brand: Elster Instromet Pages: 89
Rockwell Automation 6181P User Manual preview
6181P
Brand: Rockwell Automation Pages: 124
7starlake SR10M User Manual preview
SR10M
Brand: 7starlake Pages: 59
MSI B450M PRO-VDH MAX Manual preview
B450M PRO-VDH MAX
Brand: MSI Pages: 34
TAMS 70488 Installation & Operation Manual preview
70488
Brand: TAMS Pages: 19

Brands by name

Popular brands

Load more brands