HP A7L26UT#ABA Maintenance And Service Manual Download Page 149 | Manualshive

Page: 149 / 200

background image

Table C-2

Diagnostic Front Panel LEDs and Audible Codes (continued)

Activity

Beeps

Possible Cause

Recommended Action

Red Power LED flashes ten
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.

10

Bad option card.

1.

Check each option card by removing the
card (one at a time if multiple cards), then
power on the system to see if fault goes
away.

2.

Once a bad card is identified, remove and
replace the bad option card.

3.

Replace the system board.

Red Power LED flashes
eleven times, once every
second, followed by a two
second pause. Beeps stop
after fifth iteration but LEDs
continue until problem is
solved.

11

The current processor
does not support a
feature previously
enabled on this system.

1.

Install a TXT capable processor.

2.

Disable TXT in the Computer Setup (F10)
utility.

3.

Reinstall the original processor.

System does not power on
and LEDs are not flashing.

None

System unable to power
on.

Press and hold the power button for less than 4
seconds. If the hard drive LED turns green, the
power button is working correctly. Try the
following:

1.

Check that the voltage selector (some
models), located on the rear of the power
supply, is set to the appropriate voltage.
Proper voltage setting depends on your
region.

2.

Replace the system board.

OR

Press and hold the power button for less than 4
seconds. If the hard drive LED does not turn on
green then:

1.

Check that the unit is plugged into a
working AC outlet.

2.

Open hood and check that the power button
harness is properly connected to the
system board.

3.

Check that both power supply cables are
properly connected to the system board.

4.

Check to see if the 5V_aux light on the
system board is turned on. If it is turned on,
then replace the power button harness. If
the problem persists, replace the system
board.

5.

If the 5V_aux light on the system board is
not turned on, remove the expansion cards
one at a time until the 5V_aux light on the
system board turns on. It the problem
persists, replace the power supply.

Interpreting POST Diagnostic Front Panel LEDs and Audible Codes 139

«
...
147
148
149
150
151
...
»

Summary of Contents for A7L26UT#ABA









































































































































































































Reviews:

No comments

Related manuals for A7L26UT#ABA

Brand: IBM Pages: 717

Brand: UMAX Technologies Pages: 34

Brand: Aaeon Pages: 64

Brand: A1Touch Pages: 8

Brand: Compaq Pages: 69

ECS-9740-505M-GTX1050

Brand: Vecow Pages: 111

Brand: Acer Pages: 84

Brand: Kontron Embedded Computers Pages: 48

Brand: Asus Pages: 80

Brand: Asus Pages: 35

Brand: Asus Pages: 56

Brand: Asus Pages: 35

Brand: Asus Pages: 69

Brand: Asus Pages: 28

Brand: Asus Pages: 28

Brand: Asus Pages: 35

Brand: Asus Pages: 2

Chromebox CN Series

Brand: Asus Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands