HP A7L26UT#ABA Maintenance And Service Manual Download Page 119

Page: 119 / 200

Disconnect the cable from the system board

(1)

, lift the fan sink from atop the processor

(2)

and

set it on its side to keep from contaminating the work area with thermal grease.

Figure 8-33

Removing the fan sink

When reinstalling the fan sink, make sure that its bottom has been cleaned with an alcohol wipe and
fresh thermal grease has been applied to the top of the processor.

CAUTION:

Fan sink retaining screws should be tightened in diagonally opposite pairs (as in an X)

to evenly seat the heat sink on the processor to avoid damage that could require replacing the system
board.

Failure to install the fan duct may cause the computer to overheat.

Fan Sink 109

Summary of Contents for A7L26UT#ABA









































































































































































































Search results

Summary of Contents for A7L26UT#ABA

Reviews:

Related manuals for A7L26UT#ABA

Brands by name

Popular brands

HP A7L26UT#ABA, Maintenance And Service Manual

Search results

Summary of Contents for A7L26UT#ABA

Reviews:

Related manuals for A7L26UT#ABA

Brands by name

Popular brands