HP 175X - JetDirect Print Server Administrator'S Manual Download Page 86

Page: 86 / 302

ENWW

TCP/IP Configuration 86

802.11 Wireless Diagnostics

Command

Description

Current SSID

(Read-only parameter) The network name (SSID) to which
the wireless print server connected.

Current Channel

(Read-only parameter) The channel that the wireless print
server is currently using.

Signal Strength

(Read-only parameter) The strength of the radio signal
received by the print server.

<blank>

: No radio signal detected while the print server is

scanning.

No Signal

: No radio signal detected on any channel.

Poor/Marginal/Good/Excellent

: Indicates the detected

signal strength level.

Access Point Mac

(Read-only parameter) The Media Access Control (MAC)
address of the Access Point used for Infrastructure mode
communications. For example,

00:a0:f8:38:7a:f7

specifies that the Access Point with MAC address
00a0f8387af7 was used for communicating on the network.

TCP/IP Main Settings

Command

Description

host-name

Alphanumeric string (up to 32 characters), to assign or
change the name of the network device. For example,

“host-name printer1” assigns the name “printer1” to the

device.

ip-config

Specify the configuration method:

manual

: The print server will wait for IP parameters using

manual tools (such as Telnet, embedded Web server,
control panel, installation/management software). Status
will be

User Specified

bootp

: The print server will send BOOTP requests on the

network for dynamic IP configuration.

dhcp

: The print server will send DHCP requests on the

network for dynamic IP configuration.

IP address for the print server, in dotted notation. For
example:

ip-config manual

ip 192.168.45.39

where

ip-config

specifies manual configuration and

manually sets the IP address 192.168.45.39 on the print
server.

Specifying 0.0.0.0 clears the IP address.

If you exit and save a new IP address, it must be specified
on the next Telnet connection.

Table 3.4

Telnet Commands and Parameters (6 of 18)

Summary of Contents for 175X - JetDirect Print Server















































































































































































































































































































Search results

Summary of Contents for 175X - JetDirect Print Server

Reviews:

HP 175X - JetDirect Print Server, Administrator'S Manual, Page: 86 / 302

Search results

Summary of Contents for 175X - JetDirect Print Server

Reviews: