HP 175X - JetDirect Print Server Administrator'S Manual Download Page 19

Page: 19 / 302

ENWW

HP Software Solutions Summary 19

HP IP/IPX Printer Gateway for NDPS

NetWare 5.x, 6.0

(IPX only)

Simplified installation,
printing, and bidirectional
management of
HP Jetdirect-connected
printers under Novell
Distributed Print Services
(NDPS).

Allows automatic
discovery and installation
of HP Jetdirect-connected
printers into NDPS.

●

Frees up user licenses

●

Allows disabling of
SAPs to reduce
network traffic

●

Requires HP Jetdirect
firmware version
x.20.00 or later

HP WPS Assistant (Mac OS X)

Mac OS X 10.1.5 or later

Configuration of HP
Jetdirect wireless print
servers with a connection
to your network.

●

Requires HP Jetdirect
wireless print servers
with firmware version
x.24.00 or later

●

Distributed on the HP
Jetdirect CD-ROM

HP LaserJet Utilities for Mac OS

Mac OS 9.x, X (Classic
Mode)

Configuration and
management of
HP Jetdirect-connected
printers.

Table 2.1

Software Solutions (3 of 3)

Operating Environment

Function

Remarks

Summary of Contents for 175X - JetDirect Print Server















































































































































































































































































































Search results

Summary of Contents for 175X - JetDirect Print Server

Reviews:

HP 175X - JetDirect Print Server, Administrator'S Manual, Page: 19 / 302

Search results

Summary of Contents for 175X - JetDirect Print Server

Reviews: