manualshive.com logo in svg

HP 175X - JetDirect Print Server, Administrator'S Manual, Page: 100 / 302

Share
Download
HP 175X - JetDirect Print Server Administrator'S Manual Download Page 100

ENWW

TCP/IP Configuration 100

Using Telnet to Erase the Existing IP Settings

To erase the IP address during a Telnet session, use the following 
command line entries: 

1. Type 

cold-reset

, then press 

Enter

.

2. Type 

quit

, then press 

Enter 

to exit Telnet.

3. Power the print server off/on.

Note

This procedure resets all TCP/IP parameters, but 
only affects the TCP/IP subsystem.  Parameters for 
other subsystems such as IPX/SPX or AppleTalk are 
not affected. 

To reset all parameters to factory default values, 
refer to 

Chapter 8

.

Using the Embedded Web Server

You can set IP parameters on HP Jetdirect print servers that 
support the embedded Web server. For more information, refer to 

Chapter 4

.

Summary of Contents for 175X - JetDirect Print Server















































































































































































































































































































Reviews:

No comments