13
GB
DATA PLATE
Dimensions
width cm 44
height cm 32.5
depth cm 45.5
Volume
lt. 65
Electrical
connections
voltage: 220-240V ~ 50/60 Hz or
50Hz (see data plate)
maximum power absorbed 2250W
Directive 2002/40/EC on the label
of electric ovens.
Standard EN 50304
ENERGY LABEL
Declared energy for Natural
convection Class – heating mode:
=
Convection mode
This appliance conforms to the
following European Economic
Community directives:
- 2006/95/EEC of 12/12/06 (Low
Voltage) and subsequent
amendments;
- 2004/108/EEC of 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments;
- 93/68/EEC of 22/07/93 and
subsequent amendments.
- 2002/96/EC and subsequent
amendments.
E
l
e
c
tri
c
a
l
c
onne
c
tions
!
Ovens equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the data plate located on the appliance (
see below
).
F
itting
t
h
e
po
w
er
s
u
ppl
y
ca
b
le
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(
see diagram
).
2. Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3. Remove the wire
contact screws L-N-
, then fasten the wires
under the screw heads,
respecting the colour
code: Blue (N), Brown
(L) and Yellow-Green
Verde ( ).
C
onnecting
t
h
e
s
u
ppl
y
ca
b
le
to
t
h
e
m
ains
Install a standardised plug corresponding to the
load indicated on the data plate (
see side
).
The appliance must be directly connected to the
mains using an omnipolar circuit-brea
k
er with a
minimum contact opening of 3 mm installed between
the appliance and the mains, suitable for the load
indicated and complying with current electrical
regulations (the earthing wire must not be interrupted
by the circuit-brea
k
er). The supply cable must not
come into contact with surfaces with temperatures
higher than 50°C.
!
The installer must ensure that the correct electrical
connection has been made and that it is compliant
with safety regulations.
Before connecting to the power supply, ma
k
e sure
that:
The appliance is earthed and the plug is
compliant with the law.
The soc
k
et can withstand the maximum power of
the appliance, which is indicated on the data
plate (
see below
).
The voltage must be in the range between the
values indicated on the data plate (
see below
).
The soc
k
et is compatible with the plug of the
appliance. If the soc
k
et is incompatible with the
plug, as
k
an authorised technician to replace it.
D
o not use extension cords or multiple soc
k
ets.
!
Once the appliance has been installed, the power
supply cable and the electrical soc
k
et must be
easily accessible.
!
The cable must not be bent or compressed.
!
The cable must be chec
k
ed regularly and replaced
by authorised technicians only (
see Assistance
).
!
T
h
e
m
an
u
f
act
u
rer
declines
an
y
lia
b
ilit
y
s
h
o
u
ld
t
h
ese
sa
f
et
y
m
eas
u
res
not
b
e
o
b
ser
v
ed
.
Summary of Contents for FH 21 IX/HA
Page 47: ...47 PT...
