EN
Viper 90mm EDF
6
Transmitter Setup
(
BNF Basic
)
IMPORTANT:
After you set up your model, always rebind the transmitter and
receiver to set the desired failsafe positions.
The GEAR Channel (CH 5) controls the retractable landing gear. If you are using a 6
channel transmitter, The FLAP Channel (CH 6) can be used to toggle SAFE Select.
With the values listed below it will turn SAFE on for half and full flap positions and
AS3X will be on for no flaps position.
To use the flap channel for the SAFE Select switch the values must be set to
+100 and -100 and the speed set to 0 temporarily to assign the safe switch in the
flap system menu. Then change the flap systems values back to the listing in the
TX setup. See the SAFE Select Switch Designation section of this manual to assign
the switch for SAFE Select.
Dual Rates
Attempt your first flights in low rate. For landings, use high rate elevator.
NOTICE:
To ensure AS3X technology functions properly, do not lower rate values
below 50%. If less control deflection is desired, manually adjust the position of
the pushrods on the servo arm
NOTICE:
If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After first flights, you may adjust expo in your transmitter.
†
Some of the terminology and function locations used in the iX12 and iX20
programming may be slightly different than other Spektrum AirWare
™
radios.
The names given in parentheses correspond to the iX12 and iX20 programming
terminology. Consult your transmitter manual for specific information about
programming your transmitter.
* Flap programming values may vary slightly. For your initial flights use
the recommended flap travel settings, and adjust the flap travel to your
preference on subsequent flights.
Computerized Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset),
then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to
100%
Set Throttle Cut to
-100%
Set Retract Channel to
Reverse
Set Aileron Expo to
High Rate 10%
Low Rate 5%
Set Elevator Expo to
High Rate 10%
Low Rate 5%
Set Rudder Expo to
High Rate 10%
Low Rate 5%
DXS
Refer to spektrumrc.com for the appropriate download setup.
DX7S
DX8
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set WING TYPE: 1 AIL; 1 FLP
4. Set FLAP SYSTEM: Choose Flap
POS 0:
100% FLAP*
0% ELEVATOR
POS 1:
0% FLAP*
-3% ELEVATOR
POS 2: -100% FLAP*
-5% ELEVATOR
Switch: SWITCH D
Speed: 2.0S
DX6e
DX6 (Gen2)
DX7 (Gen2)
DX8e
DX8 (Gen2)
DX9
DX10t
DX18
DX20
iX12
iX20
NX6
NX8
NX10
1. Go to the SYSTEM SETUP
(Model Utilities)
†
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE
(Model Setup, Aircraft Type)
†
:
WING: 1 AIL; 1 FLP
4. Set CHANNEL ASSIGN (Model Setup, Channel Assign)
†
:
(Default switch assignments with a new model setup)
Gear (CH5): SWITCH A
5. Set FLAP SYSTEM:
Switch: SWITCH D
POS 0:
100% FLAP* 0% ELEVATOR
POS 1:
0% FLAP* -3% ELEVATOR
POS 2: -100% FLAP* -5% ELEVATOR
Speed: 2.0S
The Spektrum AR637T receiver is recommended for ths airplane. If you choose to install
another receiver, ensure that it is at least a 6-channel full range (sport) receiver. Refer to
your receiver manual for correct installation and operation instructions.
Installation
(AR637T shown)
1. Mount the receiver parallel to the length of the fuselage as shown. Use heavy
duty double-sided servo tape.
NOTICE:
Incorrect installation of the receiver could cause a crash.
2. Attach the appropriate control surfaces to the their respective ports on the
receiver using the chart in the illustration.
Receiver Installation
(
ARF Plus
)
AR637 Port Assignments
BND/PRG = BIND
1 = Throttle
2 = Ailerons
3 = Elevator
4 = Rudder
5 = Retracts
6 = Flap
Summary of Contents for EFL17750
Page 66: ...IT Viper 90mm EDF 66 ...
Page 67: ...IT 67 ...
