Hoover CH90200 User Manual Download Page 4

Page: 4 / 24

OPERATION

WARNING:

Do not allow familiarity with the product to make you careless.

Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields or goggles marked to

comply with ANSI Z87.1. Failure to do so could result in fluids entering your eyes

resulting in possible serious injury.

WARNING:

Use safety equipment. Protect your eyes, skin, and lungs while

mixing, filling, spraying, and cleaning. Failure to do so may result in serious personal

injury and damage to property.

NOTICE:

Before each use, inspect the entire product for damaged, missing, or loose parts

such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are replaced. Please contact

customer service or an authorized service center for assistance.

What Solution Can You Use?

You may use this product for the purpose listed below:

• For use with most consumer grade disinfectants and sanitizing solutions.

DO NOT USE THIS SPRAYER WITH BLEACH, HYDROGEN PEROXIDE, PINE SOL OR PINE

OIL BASED SOLUTIONS. DO NOT USE WITH VINEGAR.

• Know the contents of the chemical being sprayed. Read all Safety Data Sheets

(SDS) and container labels provided with the chemical. Follow the chemical

manufacturer’s safety instructions. It is a violation of federal law to use an

EPA-approved disinfectant in a manner inconsistent with its labeling.

Filling the Tank

When adding spray solutions, you may add water and the desired chemical solution directly

into the tank, or use a solution that has been premixed in a separate container, then poured

into the sprayer, using a funnel if needed. For either method, remember:

• Liquids used must be as thin as water. Thicker liquids will not spray properly.
• Do not overfill the tank.

NOTE:

If using a measuring container or funnel to fill the tank, be sure to thoroughly

clean and rinse these items after use. If premixing the spraying solution, rinse the

container used for mixing.

TO FILL:

•  Turn off the electrostatic function and remove the battery from the unit.
•  Unscrew the cap and remove it from the tank.
•  Fill the tank with the desired liquid, up to 2 gal.

NOTE:

To ensure proper operation of the sprayer, DO NOT fill past the max fill line.

Screw the cap back onto the sprayer, making sure it is tightened securely.

NOTE:

Wipe the outside of the tank with a dry cloth and clean up any spills before

inserting the tank.

• Reinstall the battery pack.

NOTICE:

It is important to thoroughly clean the unit after each use. Allowing liquid to

remain in an idle tool for an extended period may cause its moving pieces and connectors

to seize up.

Inserting the Tank

Push the male barb on the hose onto the female quick connect on the tank.

Pull on the hose to be certain it is properly secured.

NOTE:

When using the shoulder bag option, place the tank inside the bag before

attaching the hose to the tank.

Using the Quick Connect Hose

TO ATTACH HOSE:

•  Pull back the quick-connect collar.
•  Push the hose into place onto the male barb on the back of the sprayer.
•  Push the collar forward so that the hose is secured properly.
•  Check to see that the hose is secure.

TO DISCONNECT HOSE:

• Pull back and hold the quick-connect collar.
• Remove the hose by pulling it from the quick-connect collar.

NOTE:

Be careful when disconnecting the hose from the tank because the liquid in the

hose will drain from that end. Drain remaining liquid back into container.

Connecting the Battery Pack

WARNING:

Always remove battery pack from your tool when you are

assembling parts, making adjustments, cleaning, or when not in use. Removing battery

pack will prevent accidental starting that could cause serious personal injury.

TO INSTALL:

1. Align the grooves on the battery pack with the raised ribs