background image

 

1

Chapter One – Introduction 

1.1 Performance Characteristics 

z

 

0

255 individually addressed units. The dome address is defined using a dip switch with 8 positions (Binary        

addressing scheme).             

z

 

Integrated multi-protocol and auto protocol differentiation. Note: The dome can auto differentiate the protocol of        

the Controller only on power Up. 

z

 

Continuous Pan 360 degree rotation. 

z

 

90 degree Tilt action plus 2 degree angle adjustment (the view angle can be 90 or 92 degrees). 

z

 

Pan speed in manual operation is variable from 0.1 Up to 300 degrees per second.                                      

z

 

Tilt speed in manual operation is variable from 0.1 to 120 degrees per second. 

z

 

128 preset positions. (A preset position is defined as a user definable setting for precise coordinates). 

z

 

The maximum speed when a preset position is called can reach 400 degrees per second with positioning accuracy of

±

0.1 degree.   

z

 

Input power Supply: 24VAC-2Amp (outdoor).   

z

 

User friendly on screen menu interface for ease of installation. 

z

 

Environmental protection conforming to IP66 standards (outdoor model). 

z

 

RS-485 (long distance) communications mode. 

z

 

Selectable transmission speed, (i.e. Baud rate). User definable via dip switch setting from 2400bps to 1920 bps. 

1.2 Features and Functions 

z

 

Multi-language on screen menu for operation and function settings.

The camera title is user definable as well as the 

ability to display or not the camera coordinates

z

 

On screen Crosshair function (By enabling this option, the target can be followed more effectively using the crosshairs 

as a reference point). 

z

 

Three user definable PTZ tours with Up to 2 minutes record duration for each tour. (User has the ability in real-time to 

monitor and record the action of a manual dome operation). 

Six group of programmable vector scans (including scan speed, dwell time, preset and dwell time between tours) Auto 

flip function in tilt  10 degree positioning. 

z

 

24 sectors of user programmable privacy zones (sectional mask) .User can mask part of the camera sectors which 

differs between different models of installed cameras. 

z

 

Eight sectors of user programmable sectional display. User can define and display the name and position of the camera, 

which differs between different models of installed cameras. 

z

 

Resume automatic operation after initial self-test of the dome as well as resume automatic operation when there is no 

transmission from a keyboard controller (Dwell time can be set from 1 to 999 seconds). 

z

 

Freeze frame function (Snapshot function availability Supported by camera). 

z

 

Resume operation function (Dome unit will return to the previous operation after the execution of an operation using 

the on screen menu). 

z

 

Intelligent manual scan function (By executing this function in manual pan, you can adjust the manual pan behavior of     

the dome).                                                                                                                                                                                                   

Summary of Contents for VSD-261P


































Reviews: