Honeywell TELEPHONE ACCESS MODULE W8735D Owner'S Manual Download Page 5 | Manualshive

Page: 5 / 36

Honeywell TELEPHONE ACCESS MODULE W8735D Owner'S Manual Download Page 5

5

69-2028—01

Battery Installation

The Telephone Access Module requires a 9-volt

alkaline battery (not included) to provide power to the

unit during a power outage in order to allow the unit to

dial-out an alert indicating an extended power

interruption. (See “Alert Messages” on page 8.)

CAUTION

Dead or Missing Battery Hazard.

Can prevent Telephone Access Module

from dialing power outage alert.

Check battery annually or before leaving for

extended absence.

To install or replace the battery:

1.

Press the latch on the top of the battery cover

and pull it down and away (Fig. 2).

2.

Connect the battery leads to the 9-volt battery.

3.

Insert the battery into the compartment.

4.

Insert the bottom tabs of the battery cover into

the slots on the case, then swing the battery

cover up and in until the top latch engages.

Fig. 2. Installing the Battery.

BATTERY COVER

BATTERY INSTALLED

9V BATTERY LEADS

BATTERY

COVER LATCH

M23760A

«
...
3
4
5
6
7
...
»

Summary of Contents for TELEPHONE ACCESS MODULE W8735D





































Reviews:

No comments