Honeywell TELEPHONE ACCESS MODULE W8735D Owner'S Manual Download Page 30

Page: 30 / 36

69-2028—01

Resetting All Limits To Their Factory Defaults

Press 6 from the Main menu to select the Limit Menu.

At the Limit menu, press 7. You hear “

You have

chosen to reset all limits to factory default settings.

Press # key if this is correct. Press 0 (zero) to leave

the limits unchanged

.”

TO RESET AL LIMITS TO THE FACTORY DEFAULTS:

Press the # key.

Press the * key to return to the Main menu.

The above action resets all limits to their factory

defaults. See Table 5 for the factory defaults.

TO LEAVE THE LIMITS UNCHANGED:

Press 0 (zero). You hear “

Limit menu

.”

Press the * key to return to the Main menu.

Table 5. Factory Default Settings.

Limit

Factory Setting

Indoor Low Temperature Limit

50º F (10° C)

Indoor High Temperature Limit

90º F (32° C)

Outdoor Low Temperature Limit

40º F (4° C)

Outdoor High Temperature Limit

105º F (40° C)

Humidity Low Limit

25%

Humidity High Limit

70%

Summary of Contents for TELEPHONE ACCESS MODULE W8735D





































Search results

Summary of Contents for TELEPHONE ACCESS MODULE W8735D

Reviews:

Honeywell TELEPHONE ACCESS MODULE W8735D, Owner'S Manual, Page: 30 / 36

Search results

Summary of Contents for TELEPHONE ACCESS MODULE W8735D

Reviews: