Honeywell Sensepoint XCD RTD Technical Manual Download Page 32

Page: 32 / 68

Sensepoint XCD RTD Technical Manual SPXCDHMRTEN Issue 1

(ZERO CALIBRATION)

1. If the ambient air is NOT considered reliable to use to set the ZERO, then remove

the weather protection and fit the Gassing Cap accessory (see Section 4.3) onto the

sensor and apply a clean source of zero gas or compressed air.

2. To access the calibration menu, hold the end of the magnet over the switch located

at the top center of the detector display (



) for at least 3 seconds and then remove.

3. The display will indicate the first configuration mode menu ‘SEt CAL’.

4. Put the magnet over the ‘



’ switch again and move to enter the Calibration menu.

5. The display will show the current gas reading, and the ‘ ’ icon flashes.

6. Observe the Zero reading on the XCD RTD display. If it shows a stable reading

around “0” there is no need to carry out Hardware adjustment. Skip the next step.

7. Open the sensor enclosure by unscrewing the sensor cap assembly from the sensor

main body and replace with a Gassing Cap (Part No: 2106D2097) and Flow Housing.

If the output, with no gas applied, is not zero then adjust the zero potentiometer

through the Gassing Cap access holes (see Diagram 15) to obtain a zero indication.

Diagram 15: Sensepoint Toxic Sensor Zero and Span potentiometer

Zero Pot

Span

Zero Pot

Non-Oxygen

Oxygen

Span

A compressed air cylinder (20.9%Vol oxygen) should be used to perform the zero

calibration if the area where the detector is located contains any residual amount of the

target gas. If no residual gas is present then the background air can be used to perform

the zero calibration. Contact your Honeywell Analytics representative for details of suitable

calibration kits.

To calibrate the detector follow the procedure below.

Note: the Oxygen sensor does not require a zeroing procedure. Background air

(20.9%Vol oxygen) can be used to span the oxygen sensor in place of a compressed

air cylinder (20.9%Vol oxygen). For oxygen sensors only do parts 1-4, 13, 14 (if

compressed air cylinder is used), 15-17 and 22 of the procedure below.

Summary of Contents for Sensepoint XCD RTD





































































Search results

Summary of Contents for Sensepoint XCD RTD

Reviews:

Related manuals for Sensepoint XCD RTD

Brands by name

Popular brands

Honeywell Sensepoint XCD RTD, Technical Manual

Search results

Summary of Contents for Sensepoint XCD RTD

Reviews:

Related manuals for Sensepoint XCD RTD

Brands by name

Popular brands