Honeywell #HZ-7000 - Sure-set Digital Heater Fan Installation And User Manual Download

Page: 15 / 74

UltraKey Plus Controller Installation and User Guide

Document 800-02573 Rev B

11/2009

About this Document and the UltraKey Plus

In this section:

•

Document Overview, page 15

•

Finding More Information, page 16

•

Typographical Conventions, page 16

•

UltraKey Plus Specifications, page 17

•

Shipping Checklist, page 18

•

UltraKey Plus Port Connections and Descriptions, page 19

The UltraKey Plus (HJK7000) is a replacement for the Honeywell Ultrakey (HEGSA002)
controller and is compatible with Honeywell VideoBloX and MAXPRO-Net Video Matrix
Systems.

The UltraKey Plus has these modes available, depending on the installation:

•

MAXPRO: For use with MAXPRO-Net Matrix System installations.

•

VideoBloX: For use with VideoBloX Matrix System installations.

Document Overview

This user guide includes:

•

UltraKey Plus controller user instructions (

Chapter 1

•

Installation/connection and configuration instructions specific to VideoBloX
(

Chapter 2

)

•

Installation/connection and configuration instructions specific to MAXPRO-Net
(

Chapter 3

•

System Administration and troubleshooting (

Chapter 4

)

Summary of Contents for #HZ-7000 - Sure-set Digital Heater Fan











































































Search results

Summary of Contents for #HZ-7000 - Sure-set Digital Heater Fan

Reviews:

Related manuals for #HZ-7000 - Sure-set Digital Heater Fan

Brands by name

Popular brands

Honeywell #HZ-7000 - Sure-set Digital Heater Fan, Installation And User Manual

Search results

Summary of Contents for #HZ-7000 - Sure-set Digital Heater Fan

Reviews:

Related manuals for #HZ-7000 - Sure-set Digital Heater Fan

Brands by name

Popular brands