Honeywell #HZ-7000 - Sure-set Digital Heater Fan Installation And User Manual Download

Page: 48 / 74

Installing UltraKey Plus with MAXPRO-Net

Installing and Configuring an Ethernet Connection

Step 1: Connect to the UltraKey Plus Ethernet Port

To connect to the UltraKey Plus Ethernet port:

Plug an RJ45 network cable from the network to the controller Ethernet port. Up to 99
controllers can be connected to the network. See

Figure 3-8

Connect MAXPRO-Net to the network. Refer to the applicable

MAXPRO-Net

Installation Guide

for instructions.

Figure 3-8

Ethernet Port Connections to MAXPRO-Net

Step 2: Set and Configure for an Ethernet Connection

To set and configure for an Ethernet connection:

Apply AC power to the controller after all the devices have been connected

correctly.

Press Alt + Clr + Home keys on the controller to

display the Login page

Enter the PIN password 3434.
The Settings screen displays.

Table 3-2

RJ45 Ethernet Pin Assignments

Port

Pin

Signal

RJ45 Ethernet

TX +

TX -

RX+

RX-

MAXPRO-Net

Ethernet Port

RJ45 network cables

Ethernet Port

Controller 1

Controller 32

TCP/IP

Network

TCP/IP

Summary of Contents for #HZ-7000 - Sure-set Digital Heater Fan











































































Search results

Summary of Contents for #HZ-7000 - Sure-set Digital Heater Fan

Reviews:

Related manuals for #HZ-7000 - Sure-set Digital Heater Fan

Brands by name

Popular brands

Honeywell #HZ-7000 - Sure-set Digital Heater Fan, Installation And User Manual

Search results

Summary of Contents for #HZ-7000 - Sure-set Digital Heater Fan

Reviews:

Related manuals for #HZ-7000 - Sure-set Digital Heater Fan

Brands by name

Popular brands