background image

- 11 -

opening the valve

 

f

Use the 

AUTO/ECO/MANU

 button to change to 

automatic mode.

– or –

 

f

Set the desired temperature in manual operation.

Child-proofing / operation lock

You can block the radiator controller to protect it against 
unauthorised operation:

 

f

Keep the 

AUTO/ECO/MANU

 and 

PROG

 buttons 

pressed simultaneously for at least 3 seconds. 

The symbol   is displayed.

i

The same key combination is used to release the 
radiator controller again for operation.

11. Help with problems

Error table

Problem/
Display

Cause

Remedy

 flashes

Batteries flat

Replace the batteries.

e1 
sensor

Device defective

Replace the device.

e2 
valve

Motor cannot be 
moved.

Check the 
installation. If 
appropriate, remove 
the dirt.

The radiator 
does not 
become cold.

The radiator valve 
does not close 
fully.

Check the 
installation. If 
appropriate, change 
to full-stroke mode 
(Parameter 8).

The room 
does not heat 
up during 
optimisation

Heating is not 
switched on in 
time

Ensure that the 
heating system is 
switched on.

Motor does not 
move

Valve baseplate 
not interlocked

Set the slide to the 
position

 

.

Emergency operation when batteries are flat

1. Unlock the radiator controller. To do so, slide the slide 

at the radiator controller towards the 

.

2. Pull the radiator controller off the valve baseplate.
3. Operate the radiator valve by hand using the 

adjustment dial on the valve baseplate.

+

Restoring the factory setting

1. Keep the 

PROG

 button pressed for approximately 

10 seconds until Parameter 1 flashes (left-hand digit). 

2. Use the adjustment dial to select Parameter 16 (left-

hand digit) and Setting 1 (right-hand digit). 

3. Press the 

 OK 

 button to restore the factory setting.

12. technical data

Type

HR30

Protection class

IP30

Supply voltage

Batteries 2 x 1.5 V; 
type LR6, AA, AM3

Connection to the radiator

M30 x 1.5 

Ambient temperature

0 ... 50 °C

Dimensions

94 x 50 x 69 mm

Ambient conditions

For living area, business and 
trade sections as well as 
small businesses

Humidity

10 ... 90% rel. humidity

13. Disposal

The radiator controller has to be disposed of in 
accordance with WEEE directive 2002/96/EC – 
Waste Electrical and Electronic Equipment directive.

 

f

Dispose of the packaging and product 
in a corresponding recycling centre.

 

f

Do not dispose of the unit with the 
domestic refuse.

 

f

Do not burn the product.

Summary of Contents for homexpert Rondostat COMFORT+ HR30













Reviews: