Honeywell Galaxy Flex Installer Manual Download Page 47

Page: 47 / 246

Galaxy Flex Installer Manual

Walk Test [31, Quick Menu 5]

Test options

Walk Test [31, Quick Menu 5]

Walk Test menu

31 = Walk Test

1 = View – not used

2 = Activate

1 = Silent

1 = Test all Zones

2 = Selected Zones

2 = Audible

1 = Test All Zones

2 = Selected Zones

View [31.1] Not used

Activate silent test on all zones [31.2.1.1] &
Activate audible test on all zones [31.2.2.1]

Use these options to starts an immediate walk test on all zones that have the omit attribute
enabled (refer to

Program Zones [52]

). Non-omittable zones are not included and remain

active throughout the test. If all zones are non-omittable

NO ENTRIES

is displayed.

Activate silent test on selected zones [31.2.1.2] &
Activate audible test on selected zones [31.2.2.2]

Use these options to select specific zones to test.

Navigate to a zone you want to test (use

or type a zone number).

Press

to toggle the test status to TEST.

Repeat the steps above until you have selected all the zones you wish to test.

Press

ent

to start the test.

Alternatively:

Press

to include all zones.

Navigate to any zones you wish to exclude (press

to exclude a zone).

Press

ent

to start the test.

Summary of Contents for Galaxy Flex























































































































































































































































Search results

Summary of Contents for Galaxy Flex

Reviews:

Honeywell Galaxy Flex, Installer Manual, Page: 47 / 246

Search results

Summary of Contents for Galaxy Flex

Reviews: