manualshive.com logo in svg

Honeywell Galaxy Flex, Installer Manual, Page: 151 / 246

Share
Download
Honeywell Galaxy Flex Installer Manual Download Page 151

Galaxy Flex Installer Manual 

Communications [56]

 

 

151 

Listen-In [56.7.1] 

Use this option to allow onsite audio verification by an operator, after the panel sends an 
alarm signal to the ARC. 

0=Disabled

 

No audio on any number. 

1=Tel No. 1/2/3

   All telephone numbers are used to transmit all calls, including audio and 

non-audio events. 

2=Tel No. 3

 

Alarms enabled with audio are reported to telephone no 3 only (entered 
with option 

56.1.18

), and the audio follows on the same number. No 

audio is sent to Primary(TEL 1) / Secondary(TEL 2). 

Alarm Monitoring [56.7.2] Not Used 

Dial In [56.7.3] Not Used 

Audio Module [56.7.4] 

This option enables the Audio Interface Module and configures the audio channels that will 
be used to record sound in the event of an alarm. 

1=Path (PSTN) 

This option selects PSTN as the communication line between the 
panel and ARC when set to 1=Enabled. 

2=Audio Channels 

This option controls the audio channels’ status. It can be enabled or 
disabled. 

The channel is in a four-digit format. For example: Channel 9024. 

9=Line number (fixed) 

0=Audio Interface number (fixed) 

2=Mux Module number 

4=Audio channel 

Press

 ent 

to display the status of the current audio channel, for example: 

 

Press

 ent 

again to disable the audio channel. 

 

Pre Alarm [56.7.5] 

Use this option to set the alarm delay recording time. The audio channel continuously 
records a rolling 10 seconds of audio. When an alarm activation occurs, the system stops 
recording and stores 10 seconds of audio. Use the pre-listen time parameter to set the 
amount of alarm delay in the recorded audio. 

CHANNEL  9024 
[ent] to select 

ENABLED  9024 E 
0=DISABLED 

E = enabled, D = disabled 

Summary of Contents for Galaxy Flex























































































































































































































































Reviews:

No comments