manualshive.com logo in svg

Honeywell Galaxy Flex, Installer Manual, Page: 150 / 246

Share
Download
Honeywell Galaxy Flex Installer Manual Download Page 150

Communications [56]

 

Galaxy Flex Installer Manual 

150 

max.) of message recipients. 

2=Centre No. 

The phone number (22 digits max.) of the SMS centre. Each operator 

has a different number.. Always use the full telephone number including the country code 
for the centre number. Start the number with a 

 in place of the zero. 

3=Format 

The option is: 

1=SMS 

For mobile phones 

4=Site ID       

A 16 character alphanumeric string used to identify the panel/site sending the 

message. 

USB [56.6] 

 

 

  

 1 = Format 

 

 

 

 

 

 1 = SIA (0-4) 

 

 

 

 

 

 

 

 1 = Trigger (1 = Status, 2 = Groups) 

 

 

 

 

 

 

 2 = Microtech (Same as SIA format) 

 

 

 

 

 2 = Account No. (6 digits maximum) 

SIA Format [56.6.1.1] 

For details see 

Int Telecom SIA Format [56.1.01.2]

. 

Microtech Format [56.6.1.2] 

For details see 

Int Telecom Microtech Format [56.1.01.3]

. 

Account No. [56.6.2] 

This is the site identifier. Enter a unique account number (6 digits maximum). 

Audio [56.7] 

Use this option to setup Audio Transmission to allow audio verification of an alarm. Each 
system zone can be assigned one audio channel, each with a maximum of three 
microphones. Following an alarm transmission over PSTN, you can program the panel to 
route recorded audio from the time of the alarm activation, and live audio, direct to the 
Alarm Receiving Centre. The following options are available: 

 

 

 

 1 = Listen In 

 

 

 

 

 

 

 0 = Disabled 

 

 

 

 

 

 1 = Tel No. 1/2/3 

 

 

 

 

 

 2 = Tel No. 3 

 

 

 

 2 = Alarm Monitoring – Not used 

 

 

 

 3 = Dial In – Not used 

 

 

 

 4 = Audio Module 

 

 

 

 

 

 1 = Path (PSTN) (0 = Disabled, 1 = Enabled) 

 

 

 

 

 

 2 = Audio Channels – Channel No (0 = Disabled, 1 = Enabled) 

 

 

 

 5 = Pre-Alarm – Pre Listen Time 00 (0 to 10 sec) 

Summary of Contents for Galaxy Flex























































































































































































































































Reviews:

No comments