manualshive.com logo in svg

Honeywell Ademco Vista-12D, Installation And Setup Manual

Share
Download
Honeywell Ademco Vista-12D Installation And Setup Manual Download Page 99

Testing the System

 

 

7-3 

Dialer Communication Test  

1.  Enter Installer Code + 5 [TEST], then press “1” at the prompt to start the Dialer Test. 

1=DIAL, 0=WALK 

(no special display on Fixed-Word keypads) 

 

The following will be displayed (accompanied by 2 beeps) if test is successful: 

PHONE OKAY 

(“Cd” displayed on Fixed-Word Display Keypads) 

 

A Contact ID report will also be sent (code 601) 

If the dialer test is unsuccessful, the following is displayed: 

COMM FAILURE 

(“FC” displayed on Fixed-Word Display Keypads) 

 

2.  Enter installer code + OFF to clear the display and exit. 

 

 

Automatic Standby Battery Tests 

1.  An automatic test is conducted every 3 minutes to ensure that a standby battery is 

present and properly connected.  If a battery is not present or is not properly connected, a 
“LOW BATTERY” message is displayed and, if so programmed, will be reported to the 
central station. 

 

2.  A battery capacity test is automatically conducted for 2 minutes every 4 hours, beginning 

4 hours after exiting the Programming mode or after powering up the system.  In 
addition, entry into the Test mode will also cause a battery capacity test to be initiated. If 
the battery cannot sustain a load, a “Low Battery” message is displayed and, if so 
programmed, will be reported to the central station. 
 

 

Summary of Contents for Ademco Vista-12D

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands