manualshive.com logo in svg

Honeywell Ademco Vista-12D, Installation And Setup Manual

Share
Download
Honeywell Ademco Vista-12D Installation And Setup Manual Download Page 57

 

 

5-1 

S E C T I O N   5  

Menu Mode Programming 

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

 

About Zone Programming (

∗∗∗∗

56 and 

∗∗∗∗

58 Menu Modes) 

∗

56 Zone Programming is used to program zones, zone types, report codes, enroll 5800 RF 

Wireless Transmitter serial numbers, and identify the type of loop input device(s). This mode 
can also be used to enter alpha descriptors for programmed zones; however, we recommend 
entering descriptors in menu mode 

∗

82 (

Alpha Descriptor Programming

 after all zone 

programming has been completed). 
For a faster method of zone programming, you can use the 

∗

58 Expert Programming Mode 

instead of 

∗

56 Zone programming. The 

∗

58 Expert Programming Mode is designed for those 

who have had previous experience in programming control panels of this type. 

 

NOTE:

 Alpha display prompts are shown in a double-line box. 

 

∗∗∗∗

56 Zone Programming Procedure 

Zone Programming involves: 
1. Entering the zone number to be programmed; 
2. Making appropriate entries at the prompts; 
3. Confirming the serial number of wireless transmitter zones. 

 

Start Zone Programming mode by pressing 

∗

56 while in Data Programming mode. The 

following prompts are displayed:  

 

PROMPT 

VALID ENTRIES

 

EXPLANATION

 

 

 

 

 

SET

 

TO CONFIRM? 

0 = NO  1 = YES 

 

Set to Confirm

 

0 = no 
1 = yes

 

If 1 (Yes) is entered, the XMIT TO CONFIRM 
prompt appears later in this procedure after 
entering RF transmitter serial and loop numbers, 
and lets you confirm the programming of each RF 
transmitter.

 We recommend that you confirm 

every transmitter.

 

 

If 0 (No) is entered, the XMIT TO CONFIRM 
prompt is automatically skipped. 

 

This option is ignored if programming wired zones 
only. 

 

 

 

Summary of Contents for Ademco Vista-12D

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands