Honeywell Ademco Vista-12D Installation And Setup Manual Download Page 44

Page: 44 / 112

Installation and Setup Guide

4-8

FIELD

TITLE and DATA ENTRIES

EXPLANATION

*63

Low Battery Report Code

0 = disable; 1-F = see description above

∗

Sent when a low-battery condition exists in the
system’s battery.

*64

Test Report Code

0 = disable; 1-F = see description above

∗

Sent periodically to test that the communicator and
phone lines are operational. Frequency of report is set in
Scheduling mode (event 11).

*65

Open Report Code

0 = disable; 1-F = see description above

∗

Sent upon disarming of the system in the selected
partitions.

*66

Arm Away/Stay Report Code

0 = disable; 1-F = see description above

∗

This option allows for independent programming of
Away and Stay reports for each partition.

NOTE:

“OPEN” reports are not sent if the associated

closing report is not enabled.

*67

RF Low Battery Report Code

0 = disable; 1-F = see description above

∗

Sent when a wireless transmitter low-battery condition
exists.

*68

Cancel Report Code

0 = disable; 1-F = see description above

∗

Sent upon disarming of the system after an alarm
condition was reported.

*69

Alarm Restores

Send restore code (if fault cleared):
0 = at siren timeout (if restored) or at disarm

(whether restored or not)

1 = dynamically as the fault clears
2 = only after a disarm

Alarm restore message will be sent upon condition
selected.

*70

Alarm Restore Report Code

0 = disable; 1-F = see description above

∗

Sent when an alarm zone is restored to its non-faulted
condition or at the times selected in field *69.

*71

Trouble Restore Report Code

0 = disable; 1-F = see description above

∗

Sent when a trouble in a zone is restored

*72

Bypass Restore Report Code

0 = disable; 1-F = see description above

∗

Sent when a zone that has been bypassed is
unbypassed, either manually or when the
partition/system is disarmed.

*73

AC Mains Restore Report Code

0 = disable; 1-F = see description above

∗

Sent when AC mains has been restored after an AC
mains outage.

*74

Low Battery Restore Report Code

0 = disable; 1-F = see description above

∗

Sent when a system low-battery condition is restored
to normal.

*75

RF Low Battery Restore Code

0 = disable; 1-F = see description above

∗

Sent when a transmitter’s low battery condition is
restored (i.e., new battery installed).

*76

Test Restore Report Code

0 = disable; 1-F = see description above

∗

Sent when the Test mode is exited.

Summary of Contents for Ademco Vista-12D
















































































































Search results

Summary of Contents for Ademco Vista-12D

Reviews:

Brands by name

Popular brands

Honeywell Ademco Vista-12D, Installation And Setup Manual

Search results

Summary of Contents for Ademco Vista-12D

Reviews:

Brands by name

Popular brands