manualshive.com logo in svg

Honeywell Ademco Vista-12D, Installation And Setup Manual

Share
Download
Honeywell Ademco Vista-12D Installation And Setup Manual Download Page 92

Installation and Setup Guide 

 

 

6-8 

Keypad Commands (cont’d.) 

 

Arming Away 

Enter code + AWAY [2] or simply press appropriate lettered key on the 
keypads (see “Single-Button Arming” above). If the “Auto-Stay Arm” 
feature is enabled and the entry/exit door

 is not

 opened and closed 

within the programmed exit delay time, the system will automatically 
arm in STAY mode if armed from a wired keypad (non-RF device). If the 
door 

is

 opened and closed within the exit delay period, the system arms 

in AWAY mode. 

Arming Stay 

Enter code + STAY [3] or simply press appropriate key on the keypads 
(see “Single-Button Arming” above). See “Arming Away” above for Auto-
Stay arming feature. 

Arming Night-Stay 

Enter code + STAY [3] + STAY [3] or simply press appropriate key on the 
keypads (see “Single-Button Arming” above). 

Arming Instant  

Enter code + INSTANT [7]. 

Arming Maximum 

Enter code + MAXIMUM [4] or simply press appropriate lettered key on 
the keypads (see “Single-Button Arming” above). 

Disarming 

Enter code + OFF [1]. If entry delay or an alarm is active, you do not 
need to press OFF; entering the security code alone disarms the system. 

Bypassing Zones 

Enter code + BYPASS [6] + zone number(s). Can bypass while system 
armed/disarmed. 

Forced (Quick) Bypass 

To automatically bypass all faulted zones, use the “Quick Bypass” 
method. Enter code +  [#], then wait for all open zones to be 
displayed. Arm when display indicates “ZONE BYPASSED” and 
“READY TO ARM”. 

Chime Mode  

Enter code + CHIME [9]. To turn chime off, enter code + CHIME again. 

Activate Output Devices 

If relay outputs (via a 4204, 4229, or 6164), or Powerline Carrier devices 
are used, two keypad entries available to the user are included. If 
programmed, these entries can be used to manually activate or 
deactivate the device(s) for starting or stopping some action, such as 
turning lights on or off, etc.  These keypad entries are: 
[Security Code] + # + 7 + [2-digit Device #] activates (starts) that device. 
[Security Code] + # + 8 + [2-digit Device #] deactivates (stops) that 
device. 

 

Summary of Contents for Ademco Vista-12D

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands