Honeywell 60 Series Configuration Manual Download Page 4

Page: 4 / 93

Cautions and Warnings

WARNING

Installation and servicing should be performed only by qualified

and experienced technicians to conform to all local codes and to maintain your

warranty.

WARNING

To ensure compliance with electrical safety standards, CSA

Certified/UL Listed LPS or Class 2 power adapters are required. Power over

Ethernet (PoE) shall be provided by listed Information Technology Equipment

meeting the IEEE 802.3af PoE standard. The PoE is not intended to be connected

to exposed (outside plant) networks.
The Ethernet connection is not intended to be connected to exposed (outside

plant) networks. Do not connect two power sources to the camera at the same time.

WARNING

To comply with EN50130-4 requirements, a UPS should be

employed when powering the camera from 24 V AC.

Caution

Invisible LED radiation (850 nm). Avoid exposure to beam.

Regulatory Statements

Photobiological safety

This product fulfills the requirements for photobiological safety according to IEC/EN 62471
(risk group 1).

General Data Protection Regulation

Please be aware that this product can store personal data.
Personal data is protected by the General Data Protection Regulation (2016/679) in Europe
and therefore the owners of personal data have obtained certain rights thanks to this
regulation.

Summary of Contents for 60 Series






























































































Search results

Summary of Contents for 60 Series

Reviews:

Related manuals for 60 Series

Brands by name

Popular brands

Honeywell 60 Series, Configuration Manual

Search results

Summary of Contents for 60 Series

Reviews:

Related manuals for 60 Series

Brands by name

Popular brands