Honeywell 60 Series Configuration Manual Download Page 24

Page: 24 / 93

Honeywell 60 Series IP Camera Software Configuration Guide

Logging In and Viewing Live

Video

This chapter contains the following sections:

•

Logging In to the Camera via the Web Client, page 10

•

Using the Main Page, page 14

Logging In to the Camera via the Web Client

Using the web client, you can monitor live video, play back recorded video, and configure
camera settings.

Before You Begin

Before you log in to the web client, ensure that the following conditions are met:

•

The camera is properly connected to the network.

•

The camera’s IP address and the PC’s IP address are in the same network segment. If
there is a router, set the corresponding gateway and subnet mask.

•

A network connection has been established. To check this, ping the camera’s IP address.
(Enter "ping [IP address]").

Logging In to the Camera

Logging In via Internet Explorer

Open

Internet Explorer

, type the camera’s IP address in the address bar, and then click

Enter

. For example, if your camera’s IP address is

192.168.1.108

, you would type

https://192.168.1.108

Note

Internet Explorer 11 with ActiveX plug-in is supported.

The following window is displayed. Click

Continue to this website (not recommended)

Summary of Contents for 60 Series






























































































Search results

Summary of Contents for 60 Series

Reviews:

Related manuals for 60 Series

Brands by name

Popular brands

Honeywell 60 Series, Configuration Manual

Search results

Summary of Contents for 60 Series

Reviews:

Related manuals for 60 Series

Brands by name

Popular brands