background image

SAPPHIRE COMPACT FIXED FIRE SUPPRESSION SYSTEM 

LOCAL ALARM UNITS

2019-SEP-30    REV. 00    PAGE 1

Burlingham House, Hewett Road, Gapton Hall Industrial Estate, Great Yarmouth, NR31 0NN 

|

  +44 (0)1 493 417600

www.hygood.com 

|

  © 2019 Johnson Controls. All rights reserved. All specifications and other information shown were  

current as of document revision date and are subject to change without notice. 

|

  Part No. HY-2019023

PRINCIPLES OF OPERATION 

HYGOOD® SAPPHIRE® COMPACT Local Alarm Units 

are intended to enable system installers to offer full and 

complete monitoring of the health and status of HYGOOD 

SAPPHIRE COMPACT Fixed Fire Suppression System 

installations.
They offer alarm indications comprising of both an initial 

combined 30 second sounder and flashing beacon, followed 

by a continuous flashing beacon.
The alarm units come in three colour options for the beacon. 

Each colour has two base unit options that are activated 

by either 

Normally Open

 (N/O) or 

Normally Closed

 (N/C) 

switches. The three colour options are orange, blue, and 

red.

Alarm unit

Description
Orange - low pressure alarm

The low pressure alarm indicates when SAPPHIRE COMPACT pressure is below the lowest 

normal system operating pressure. This occurs at the lowest system operating temperature.
The low pressure alarm triggers through a pressure gauge with a switch contact. Use a 

higher pressure switch contact if two fitted.

Blue - system discharged alarm

The system discharged alarm indicates when the SAPPHIRE COMPACT system discharged.
The system discharged alarm triggers through a pressure gauge with a switch contact, 

pressure switch, or integrated control valve activation switch. Use a lower pressure switch 

contact if two fitted.

Red - system isolated alarm

The system isolated alarm indicates when the SAPPHIRE COMPACT system valve is closed.
The system isolated alarm triggers through an integrated ball valve position switch, where 

available.

Part No.

Description

Notes

309150001

Low pressure alarm with orange lens

For use with 

Normally Open 

contacts 

(N/O) when conditions are good. 

(Contacts close on alarm).

309150002

System discharged alarm with blue lens

309150003

System isolated alarm with red lens

309150004

Low pressure alarm with orange lens

For use with 

Normally Closed

 contacts 

(N/C) when conditions are good. 

(Contacts open on alarm).

309150005

System discharged alarm with blue lens

309150006

System isolated alarm with red lens

Summary of Contents for SAPPHIRE COMPACT 309150001







Reviews: