Honda MSX125 2017 Page 81 Owner'S Manual Download

Page: 81 / 108

Tyre Puncture

Removing Wheels

ou
bles

hoo

ting

Remove the rear axle shaft, washer, right
side collar, left side collar and rear wheel.

Support the brake caliper assembly so
that it doesn’t hang from the brake
hose. Do not twist the brake hose.

Avoid getting grease, oil, or dirt on the
disc or pad surfaces.

Do not push the brake pedal while the
brake caliper is removed.

Installation

To install the rear wheel, reverse the
removal procedure.

Take care to prevent the brake caliper
from scratching the wheel during
installation.

Make sure that the lug on the brake
caliper bracket is positioned in the slot on
the swingarm.

NOTICE

When installing the brake caliper into position, carefully
fit the brake disc between the pads to avoid scratching
them.

Brake caliper bracket

Swingarm

Slot

Lug

17 MSX125 (LO CA)-32K26D200.book 76 ページ２０１７年２月１４日　火曜日　午前１０時２２分

Summary of Contents for MSX125 2017













































































































Search results

Summary of Contents for MSX125 2017

Reviews:

Related manuals for MSX125 2017

Brands by name

Popular brands

Honda MSX125 2017, Owner'S Manual

Search results

Summary of Contents for MSX125 2017

Reviews:

Related manuals for MSX125 2017

Brands by name

Popular brands