Honda MSX125 2017 Page 54 Owner'S Manual Download

Page: 54 / 108

continued

Maintenance

Spark Plug

Checking Spark Plug

For the recommended spark plug, see
“Specifications.”

P. 97

Use only the recommended type of spark
plug in the recommended heat range.

Disconnect the spark plug cap from the
spark plug.

Clean any dirt from around the spark plug
base.

Remove the spark plug using the spark
plug wrench provided in the tool kit.

Inspect the electrodes and centre
porcelain for deposits, erosion or carbon
fouling.

If the erosion or deposit is heavy,
replace the plug.

Clean a carbon or wet-fouled plug with
a plug cleaner, otherwise use a wire
brush.

NOTICE

Using a spark plug with an improper heat range can
cause engine damage.

Spark plug wrench

Spark plug cap

17 MSX125 (LO CA)-32K26D200.book 49 ページ２０１７年２月１４日　火曜日　午前１０時２２分

Summary of Contents for MSX125 2017













































































































Search results

Summary of Contents for MSX125 2017

Reviews:

Related manuals for MSX125 2017

Brands by name

Popular brands

Honda MSX125 2017, Owner'S Manual

Search results

Summary of Contents for MSX125 2017

Reviews:

Related manuals for MSX125 2017

Brands by name

Popular brands