Honda MSX125 2017 Page 99 Owner'S Manual Download

Page: 99 / 108

Fuels Containing Alcohol

fo
rma

tio

Fuels Containing Alcohol

Some conventional fuels blended with alcohol
are available in some locales to help reduce
emissions to meet clean air standards. If you
plan to use blended fuel, check that it is
unleaded and meets the minimum octane
rating requirement.

The following fuel blends can be used in your
motorcycle:

●

Ethanol (ethyl alcohol) up to 10 % by volume.

Petrol containing ethanol may be
marketed under the name Gasohol.

The use of petrol containing more than 10 %
ethanol may:

●

Damage the painting of the fuel tank.

●

Damage the rubber tubes of the fuel line.

●

Cause corrosion of the fuel tank.

●

Cause poor drivability.

If you notice any undesirable operating
symptoms or performance problems, try a
different brand of petrol.

NOTICE

Use of blended fuels containing higher than approved
percentages can damage metal, rubber, plastic parts of
your fuel system.

17 MSX125 (LO CA)-32K26D200.book 94 ページ２０１７年２月１４日　火曜日　午前１０時２２分

Summary of Contents for MSX125 2017













































































































Search results

Summary of Contents for MSX125 2017

Reviews:

Related manuals for MSX125 2017

Brands by name

Popular brands

Honda MSX125 2017, Owner'S Manual

Search results

Summary of Contents for MSX125 2017

Reviews:

Related manuals for MSX125 2017

Brands by name

Popular brands