manualshive.com logo in svg

Honda HSM1380i, Owner'S Manual

Share
Download
Honda HSM1380i Owner'S Manual Download Page 74

72

Battery run mode

Use the battery run mode to drive the snow thrower in case the engine 
does not start.
When the main shift lever is in the other position, excepting the N 
(neutral) position, the drive control warning indicator (orange) blinks and 
you can not start the battery run mode, even if the right and left steering 
levers are squeezed simultaneously for approximately 3 seconds.
– 1. Set the main shift lever in the N (neutral) position.
– 2. Release the drive clutch lever to set it in the STOP position.
– 3. Turn the engine switch to the ON position.
– 4. Squeeze the right and left steering levers simultaneously for     

approximately 3 seconds.

– 5. Both the drive control warning indicator (red) and the drive control 

warning indicator (orange) blink after squeezing the right and left 
steering levers for approximately 3 seconds. Squeeze the drive 
clutch lever when the indicators blink. 
If the drive clutch lever and the main shift lever are not operated 
within 5 seconds after the drive control warning indicators start to 
blink, the indicators stop blinking but they stay on automatically. 
The battery run mode is automatically disarmed this time, which 
prevents the snow thrower from running with the battery power. 
Return the engine switch to the OFF position and restart the engine. 
The battery run mode keeps on while the drive clutch lever is squeezed.

MAIN SHIFT LEVER

DRIVE CLUTCH LEVER

STEERING LEVER (right)

STEERING LEVER (left)

ENGINE SWITCH

DRIVE CONTROL WARNING
INDICATOR (red)

DRIVE CONTROL WARNING
INDICATOR (orange)

36V156410.book  72 ページ  ２０１８年１０月１０日　水曜日　午前１１時３０分

Summary of Contents for HSM1380i



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands