Honda HSM1380i Owner'S Manual Download Page 119 | Manualshive

Page: 119 / 130

background image

117

• If the snow depth is less than 5 cm (2 in) deep, shift to a faster speed for more efficient snow

throwing.

*1: Tell your authorized Honda snow thrower dealer about the number of blinks of the drive control
warning indicator (orange).

(4) Other troubles

SYMPTOM

POSSIBLE CAUSE

REMEDY

Chuter guide does
not operate.

Motor is overheated
(breaker tripped).

Internal protection circuit is
armed when the auger power
height adjusting part is
overheated by frequent
application of the auger control
switch. Wait for a while and
operate the switch again.

Motor or switch is faulty.

Consult an authorized Honda
dealer.

Left driver is faulty.

Auger housing
rolling does not
operate.

Auger power rolling
adjusting part is
overheated.

Internal protection circuit is
armed when the auger power
height adjusting part is
overheated by frequent
application of the auger control
switch. Wait for a while and
operate the switch again.

Auger power rolling
adjusting part is faulty.

Consult an authorized Honda
dealer.

Right driver is faulty.

Auger housing
height does not
operate.

Auger power height
adjusting part is
overheated.

Internal protection circuit is
armed when the auger power
height adjusting part is
overheated by frequent
application of the auger control
switch. Wait for a while and
operate the switch again.

Auger power height
adjusting part is faulty.

Consult an authorized Honda
dealer.

Left driver is faulty.

Drive control
warning indicator
(orange) blinks or
stays on.

Electric system is
abnormal or faulty.

Check the drive control warning
indicator (orange) for the
number of blinks (see pages 108
and 109). Consult with your
authorized Honda dealer. *1

SYMPTOM

POSSIBLE CAUSE

REMEDY

Track is worked off
from the wheels.

Track is loosened.

Check and adjust the deflection
of the track (see page 87).

Headlight does not
turn on.

Battery is dead.

Charge or replace the battery
(see pages 92 an d 102).

Fuse is blown out.

Replace the fuse (see page 95).

Bulb in the headlight is
out.

Consult with an authorized
Honda dealer.

36V156410.book 117 ページ２０１８年１０月１０日　水曜日　午前１１時３０分

«
...
117
118
119
120
121
...
»

Summary of Contents for HSM1380i



































































































































Reviews:

No comments

Related manuals for HSM1380i

Brand: Vax Pages: 16

Brand: Poulan Pro Pages: 20

Power Max 39924

Brand: Toro Pages: 32

Brand: STEELE PRODUCTS Pages: 40

Brand: Kongskilde Pages: 12

Pro Landscaping DCM587

Brand: DeWalt Pages: 136

Brand: Stanley Pages: 20

Brand: Tuchel Pages: 56

Brand: Tuchel Pages: 70

Brand: GreenWorks Pro Pages: 44

QB883, QB883H, QB1103, QB1103H

Brand: Billy Goat Pages: 8

Brand: Morphy Richards Pages: 7

Brand: Western Pages: 12

Steiner 75-70644A

Brand: Schiller Pages: 22

Brand: Tennant Pages: 76

Brand: Troy-Bilt Pages: 12

CCR Powerlite 38173

Brand: Toro Pages: 24

CCR 6053 ES Quick Clear

Brand: Toro Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands